KIMA Robot Control Library (RCL)

October 20, 2026
By Mathieux Bergeron
Article

Unprecedented real-time performance for medical robotics, running directly on your controller

Most robotic arms come with a dedicated controller: a separate box that sits between the robot and the medical device's own controller. Every command and every feedback sample has to go through it. Kinova took a different approach with KIMA, its next-generation medical-grade robotic arm. The KIMA Robot Control Library (RCL) runs directly on the OEM controller, the real-time computer already at the heart of your medical device. There is no controller in the middle, so your application gets real-time performance that has not been possible before. And a single controller can run up to four KIMA arms.

The problem with the controller in the middle

In a typical architecture, the application on the OEM controller sends commands to the robot controller, which then drives the joints. That intermediate controller runs its own cycle, buffering and scheduling. Each layer adds latency and jitter, and the timing it adds is hidden from the device developer.

It also adds hardware: one more box to integrate, mount, cable, power, cool and maintain, and one more component to account for in the medical device.

RCL runs on the OEM controller

KIMA's seven actuators sit directly on an EtherCAT network (100 Mbps, CiA 402 drive profile). Your OEM controller is the EtherCAT master, and RCL runs the real-time control loop on it, on Linux RT or QNX. RCL supports both x86 and arm64 architectures, so you can pick the computer that fits your device, from industrial PCs to compact embedded boards. Your application and the robot control run in the same real-time loop, on the same computer.

The result is best-in-class real-time control at 1 kHz, with minimal jitter and latency between your control loop and the actuators. In every cycle, your application reads joint feedback and sends commands straight to the joints, with no extra controller adding its own timing.

One controller, up to four arms

A single OEM controller hosting RCL can control up to four KIMA arms. Instead of one dedicated controller per robot, all arms share the same real-time computer and run in the same 1 kHz control loop.

Because every arm is driven from the same loop, coordinating them is straightforward: their feedback is read and their commands are sent in the same cycle, without synchronizing separate controllers over a network. This opens the door to multi-arm procedures, such as one arm holding an instrument while another positions a camera or an imaging device, with fewer components and a smaller footprint than a setup with one controller per arm.

Why it matters

  • Unprecedented real-time performance: a deterministic 1 kHz loop with minimal jitter and latency, from your code to the joints.
  • Full control of the timing: no hidden cycles or buffering from an embedded or external controller, so the arm behaves the way your control model expects.
  • Tighter integration: robot control shares the same real-time computer as the rest of your device, such as imaging, tracking or user input, so they can run in the same control loop.
  • A simpler system: one less controller means fewer components, less cabling and a smaller footprint in the operating room.
  • Multi-arm systems made simple: one controller can run up to four KIMA arms, synchronized in the same real-time loop.
  • Better data: high-rate, deterministic feedback makes logs, model identification and controller validation more reliable.

Low-level and high-level control in one library

RCL is a high-performance C++ library that gives you the level of control your application needs:

  • Low-level joint control: position (CSP), velocity (CSV) and torque (CST) commands, sent to the joints in every cycle.
  • High-level control: Cartesian position and velocity, joint position and velocity, and wrench.
  • Offline inverse kinematics, for planning and simulation.
  • Real-time loop on Linux RT or QNX, on x86 and arm64 architectures.

Butter-smooth hand guiding

In many medical procedures, the clinician positions the arm by hand. RCL makes that interaction feel natural: because hand guiding runs in the same 1 kHz real-time loop as the rest of the control, the arm responds instantly and smoothly to the user's hand, with no lag or jerk from an intermediate controller.

  • Impedance and admittance modes: choose the behavior that fits the application, from a light, transparent feel to stable, precise positioning.
  • Angular or Cartesian guiding: move the arm joint by joint, or move the tool freely in Cartesian space.
  • Axis locking: lock selected axes to constrain the motion, for example to keep the tool orientation fixed or to move along a single direction.
  • Null space control: take advantage of KIMA's seven axes to reposition the elbow while the tool stays in place, to clear space around the patient and the clinical team.

Built for medical devices

RCL was developed for KIMA's IEC 62304 Class C software. It is not a prototyping layer that must be replaced later: it is the control foundation that goes into the medical device.

For development and quick prototyping, Kinova also offers a ROS 2 package built on top of RCL. Teams can visualize, simulate and iterate in ROS 2, then integrate RCL directly in C++ when the project moves toward a product. The control library used in the lab is the same one that ships, so the path from lab to product is shorter and less risky.

KIMA at a glance

  • 7 axes, 3 kg payload, 750 mm reach, approximately 12.6 kg
  • IP54, designed for operating room environments
  • EtherCAT 100 Mbps, CiA 402, 1 kHz real-time control
  • Low-level modes: CSP, CSV, CST
  • C++ Robot Control Library (RCL) running on the OEM controller, on Linux RT or QNX, x86 or arm64
  • Up to 4 KIMA arms controlled from a single OEM controller
  • Impedance and admittance hand guiding, in angular or Cartesian mode, with axis locking and null space control

Getting started

To learn more about KIMA RCL and how to integrate it in your medical device, contact info@kinovarobotics.com.

Read more